![]() ![]() The device was turned on and it was placed just next to the iPad and the PC. But if I try to connect I get a message saying "Check whether the device is turned on and within range". The irony of it is that the headset is listed in the iPad as a discovered device and it did connect once. When I carried out an add device procedure on my PC, the name Nokia BH 503 flashed for a fraction of a second on the screen and then my laptop device was listed. It is my Nokia BH 503 stereo headset that is not connecting with the iPad. Now I have added a plug and play bluetooth dongle to my PC (Windowsw Xp) and it connects with the laptop and the iPad. My headset connects with the laptop, my iPad connects with the laptop. Well, that is my problem and I'd be very grateful if anybody can extricate me out of my predicament. Does that mean that some drivers have to be installed in the iPad before it will connect with the device? If so, then how did it connect in the first instance? Perplexing. The connection had to be done manually by using the "add device" feature in the Control Panel and after the device was located Windows took a few seconds to install some drivers before connecting with the headphone. There was one thing that I noticed when I connected the headset to the laptop. I can not understand why this is happening. But the headset persistently refuses to connect with the iPad. The iPad also connects effortlessly to the laptop. I then tried to connect it to the laptop, the connection was establised seamlessly and I was able to listen to the music that was available in the laptop. Though I tried to connect the headset to the iPad a number of times I kept getting the same message. When I tried to connect it manually I got a message asking me to see that the device was switched on and that it was within range. The next day when I switched on the headset, it did not connect to the iPad though the name of the headset, Nokia BH 503, was listed in the list of devices discoverable. The set connected with the iPad automatically and I to listened to some music for nearly an hour and then switched it off. On the first day that I purchased the Nokia bluetooth headphones, I followed the instructions in the instruction manual and charged the headset and switched it on. Unsolder it, I reloaded the headphones – the battery was 3.82V.I have an iPad, an ASUS laptop, a pair of Jembee bluetooth sterreo speakers and a Nokia BH-503 bluetooth stereo headphones. The output voltage of the controller was missing, and the battery was 2.8V. I have decided that he is guilty of the charge controller, which in the previous battery was missing, and this has been. After another charge to use once did not, well, and the next day could not turn on – have been exhausted. It was possible he borrowed normally, and then when the headphones are exhausted, they are suddenly disconnected without notifying the signal as before. Of course, I was afraid that it will not fit, but still shoved without any problems and all is well earned.Īll seemed well – after charging assembly went. Battery was there «BYT 502 030» Li-Ion 3.7v 250mAh and she was quite swollen.Ĭlimb on Ali, I decided to take a slightly larger and larger in capacity – “602030” on 300mAh $ 5, although in that case it really turned out to be written even come 320mAh. Not knowing this, I opened the first one and then another. But even after I realized that there are cogs, had to tear the foam glued to reach them, so take them apart without tearing the rather thin foam rather difficult.Īnother important point – in the ear is the buttons control board, and the battery is in the other ear. For those who want to dismantle them just say that in addition to the two visible screws, there is also hidden under a foam three pieces on the perimeter – without knowing it, I almost broke my body trying screwdriver to pry latch nonexistent. One day, after a year of correct operation, I suddenly found that they did not get to recharge – they quickly turned down as not to keep them in charge. In doing so, they actually differ from the branded headphones nokia.ĭismantling the Chinese wireless headphones BH503. If you hold these buttons a little longer, then they move to the connection mode, as evidenced by the rapid blinking of the LED. It turned out that the headphones BH503 included if at the same time hold down the “Volume +” at the end and the call button. Most of the instructions states that in order to enable it to press and hold the call button, but in my case it was not working. These headphones have been remarkable Chinese bought me at aliexpress for $ 15 and a half years ago and I even almost started to demand the return, failing to include them almost daily. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |